Browse Items (9795 total)
Sort by:
-
Correlation of temperature, velocity and perforation location in a flat unglazed transpired solar collector (Utc) due to air flow
An unglazed transpired solar collector is a system that can leverage the abundant solar energy for various purposes. The solar collector is available in flat or corrugated form and is seen to be installed as an exterior layer of building facades. The cladding thus made absorbs radiation from the sun and heats up air being sucked by fan and flowing through perforations. In this paper, the focus has been to understand the correlation of plate temperature, exit temperature, the velocity distribution in the chamber and perforation location when air flows past a flat unglazed transpired solar collector (UTC). The establishment of correlations was carried out in the dataset of flow variables obtained after solving the problem using Navier-Stokes (NS) equations along with the standard k-? turbulence model and shear stress transport (SST) k-? model. An attempt has also been made to compute Pearsons correlation coefficient of any two flow variables to understand their strong and weak correlations. A linear regression analysis has been done to predict the response variables against the response obtained in CFD solver by using an open source software Rstudio . A strong correlation among cavity vertical velocity, perforation location and temperature has been established. From the study, it is noted that the location of a perforation has a strong correlation with the cavity vertical velocity and a weak correlation exists with temperature and plate temperature. 2020, Pushpa Publishing House. All rights reserved. -
Corrigendum to Computational simulation of surface tension and gravitation-induced convective flow of a nanoliquid with cross-diffusion: An optimization procedure [applied mathematics and computation 425 (2022) 127108]
This corrigendum addresses both the physical configuration and certain typographical errors in [1] to improve clarity. These corrections do not impact the originality, results, or mathematical validity of [1]. 2024 -
Corrigendum to Implementation of modified Buongiorno's model for the investigation of chemically reacting rGO-Fe3O4-TiO2-H2O ternary nanofluid jet flow in the presence of bio-active mixers [Chemical Physics Letters, 786, 2022, 139194]
A few typographical errors have been identified in our paper titled Implementation of modified Buongiorno's model for the investigation of chemically reacting rGO-Fe3O4-TiO2-H2O ternary nanofluid jet flow in the presence of bio-active mixers. This corrigendum addresses those errors however, these errors have no impact on the obtained results. 2022 -
Corroboration of skin diseases: Melanoma, vitiligo vascular tumor using transfer learning
The precise identification of skin disease is an exigent process even for more experienced doctors and dermatologists because there is a small variation between surrounding skin and lesions, a visual affinity between different skin diseases. Transfer learning is the approach which stores acquired knowledge while solving one problem and apply that knowledge to similar problems. It is a type of machine learning task where a model proposed for a task can be used again. Transfer learning is used in various areas like image processing and gaming simulation. Image processing is an evolving field in the diagnosis of various kinds of skin diseases. Here transfer learning is used to identify three skin diseases such as melanoma, vitiligo, and vascular tumors. The inception V3 model was used as a base model. Networks were pre-trained and then fine-tuned. Considerable growth of training accuracy and testing accuracy were achieved. 2021 IEEE. -
Corrosion behavior of AlCuFeMn alloy in aqueous sodium chloride solution
Medium Entropy Alloy AlCuFeMn possesses high room temperature strength and oxidation endurance. In present work, the aqueous corrosion resistance of the as-cast as well as low temperature oxidized AlCuFeMn alloy in 3.5 wt% NaCl solution, is explored. Equimolar proportions of high purity copper, manganese, iron, and aluminum were arc melted and cast in a copper mold. The alloy primarily consists of a face-centered cubic and a body-centered cubic phase. Potentiodynamic polarization tests on the alloy after low temperature surface oxidation reveal an aqueous corrosion resistance comparable to AISI 304 steel and CoCrFeMnNi high entropy alloy. The X-ray photoelectron spectroscopic studies confirmed that the free surface in the as-cast alloy is in partially oxidized state. The same completely oxidizes after low-temperature surface oxidation. Such low temperature surface oxidation improves pitting corrosion resistance in AlCuFeMn alloy due to increased metal/oxide layer resistance. The electrochemical impedance spectroscopy tests coupled with microscopy confirmed that the principal corrosion mechanisms in the alloy are of the uniform and pitting type. The energy dispersive spectroscopy experiments indicate that a copper oxide enriched layer is formed on the surface oxidized specimen during corrosion. 2021 Elsevier B.V. -
Corrosion behaviour in friction stir processed and welded materials
This chapter presents a comprehensive study on the influence of friction stir processing/welding (FSW/FSP) on corrosion behaviour. It briefly discusses the different aspects of corrosion including corrosion types, measurement techniques and data analysis. The corrosion behaviour of a wide range of friction stir processed materials, including light weight metals such as magnesium and aluminum alloys, as well as high strength metals such as steel, has been discussed in detail. The influence of FSP parameters on the microstructural evolution, comprising grain-size and precipitate refinement along with its correlation with the corrosion properties, has been described for different materials. 2014 The authors and contributors. All rights reserved. -
Corrosion Characterization of Friction Stir Weld Dissimilar Aluminium Alloy Joints
The course of contact mix welding is quick acquiring conspicuousness in aviation, marine and car industry because of its benefits as far as mechanical strength, effect and hardness characteristics. There is as yet a requirement for sure fire consideration from the exploration local area to erosion in grating mix welding zones, hence the work introduced here centres around the consumption portrayal of the grinding mix weld divergent aluminium composite. This study looks into friction stir welding under various parametric settings and shows how corrosion happens in a sodium chloride electrolytic media under potentio-dynamic conditions. The friction stir weld joints of dissimilar alloys aluminium are constructed using three sets of parameters. Straight cylinder, taper cylinder, and straight triangular tool profiles; tool rotational speeds of 800, 1000, and 1200 rpm; tool feed rates of 100, 120, and 140 mm/min; and tool offsets of 0.5, 0 mm, and-1.5 mm. The corrosion current (Icorr) reduces as tool rotating speed increases up to 1200 rpm, after which it slightly increases due to the creation of ridges all around the periphery of the friction stir weld area. 2022, Books and Journals Private Ltd.. All rights reserved. -
Corrosion mitigation performance of disodium EDTA functionalized chitosan biomacromolecule - Experimental and theoretical approach
Disodium ethylenediaminetetraacetate salt is known for its excellent coordinating properties with the metal ions. The present study deals with the investigation of the prepared Disodium EDTA functionalized chitosan in corrosion inhibition for mild steel in 1 M HCl. The modified chitosan was characterized by spectral studies, thermal analysis, and Zeta potential studies. The corrosion inhibition efficiency (%) was evaluated using the gravimetric method and electrochemical studies. The electrochemical studies included potentiodynamic polarization, linear polarization resistance, and electrochemical impedance methods. The modified chitosan polymer showed an inhibition efficiency of 96.63% for 500 ppm at 303 K. Adsorption process obeyed Langmuir isotherm. Experimental results and theoretical calculations endorsed initial physisorption followed by a chemisorption process. Surface characterization studies supported the formation of a protective film that enabled the inhibition process. Density functional theory, Monte Carlo studies, and molecular dynamics simulation studies show a good agreement with the experimental results. Two-way Analysis of Variance was performed to test the influence of immersion period and inhibitor concentration on the corrosion rate using the statistical software IBM SPSS 20.0. A quartic model was generated as the best fit with the highest R2 value of 0.973. Design Expert software was employed for statistical modeling fit. 2021 -
Corrosion studies on low-cost solid lubricant coated stainless steel specimen
AISI 304 stainless steel is widely used in industries owing to its many desirable qualities like excellent formability, drawability and resistance to corrosion. However, AISI 304 stainless steel corrodes when exposed to halide environment such as chloride and fluoride. This study is primarily focused to assess the anti-corrosion properties of AISI 304 steel when coated with CaF2 solid lubricant. CaF2 solid lubricant was synthesized from the discarded egg-shells by ion exchange method by treating the egg-shell powder with hydrogen fluoride solution. Thermal spray coating method was used to coat the synthesized CaF2 solid lubricant on the AISI 304 stainless steel specimen. Slurry erosion test and electrochemical impedance spectroscopy test were conducted on the coated and uncoated specimen to assess the corrosion resistance. From the experimental results, the corrosion rate of the coated specimen was found to be very effective compared to the uncoated specimen. 2023 Elsevier Ltd. All rights reserved. -
Coset component signed graph of a group
In this paper, the notion of a newly derived signed graph called a coset component graph, based on cosets of subgroups of a group is introduced. Let G be a group and H be its subgroup. Then, the coset component graph of H in G, denoted by ?cc, is a simple graph with the vertex set consisting of elements of G and two vertices say, a, b ? ?cc are adjacent if either aH = bH or Ha = Hb. A coset component signed graph of H in G is a signed graph whose edges get the sign in accordance with their inclusion in the edge set of the corresponding coset component graph. The structure and important properties of the coset component signed graphs are determined in this paper. 2024 World Scientific Publishing Company. -
Cost Effective and Energy Efficient Drip Irrigation System for IoT Enabled Smart Agriculture
The conventional methods of smart farming consume a significant percentage of the resources such as water, electricity, and manpower. This approach demands more time, money, and effort. The state of the art drip irrigation methods make use of the solenoid valve to control the water flow. The problem with such a system is reflected in its power consumption which is a significant factor for large-scale demands. The method proposed in this paper addresses this problem by developing an automated drip irrigation system that replaces components used in conventional methods with its economical counterparts in the market. A system using Node MCU, DC submersible motor, and soil moisture sensor is developed to automate the irrigation process ensuring efficient water and energy consumption. Since the proposed system utilizes economically cheaper components, it provides an upper edge over other systems in terms of expenditure and in turn economically feasible for large-scale demands. A mobile application is also developed to control, monitor, and schedule irrigation processes. The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd. 2024. -
Cost effective porous areca nut carbon nanospheres for adsorptive removal of dyes and their binary mixtures
Novel porous nanospheres from areca nuts (ACNPs) were synthesized via one-step pyrolysis without the use of any chemical treatment and the materials were used as adsorbents for the removal of cationic methylene blue (MB) and anionic methyl orange (MO) as well as their binary mixtures. Around, 67 tonnes of areca nut biowaste is generated every year which are then burnt due to their slow rate of decomposition resulting in higher carbon footprints. Biosorbents are generally a preferable alternative for dye adsorption but involve chemical modification for surface enhancement and complex sample treatment. In this work, ACNPs, were investigated for their efficiency in the raw form and were characterized by SEM, EDS, FTIR, XRD, and BET techniques before and after subjecting to the dye adsorption studies. The BET analysis of the adsorbents showed a high specific surface area of 693.8 m2/g when prepared at 1000 C, while the N2 adsorption-desorption plot showed type-IV isotherm, suggesting the microporous nature of the carbon matrix. Batch equilibrium studies showed the removal efficiency of >95% for both the dyes and their binary mixtures under the optimum conditions of 0.15 g/L dosage, 10 ?M concentration and contact time of 70 min. Due to the synergistic effects of the binary dyes, higher removal efficiency of MB compared to MO was observed in the binary mixture. Adsorption results were tested using Langmuir, Freundlich, Temkin, Redlich-Peterson, and Elovich isotherms to assess the best fit of the models. The qm value of MB was found to be 97.37 mg/g, while that of MO was 71.22 mg/g which is higher compared to individual dye components having lower values of 86.12 mg/g and 50.35 mg/g, respectively. Extended Langmuir and Jain and Snoeyink isotherms were used for binary data interpretation. The kinetic results showed good agreement with the Pseudo-second order equation, indicating internal diffusion. The possible mechanism involved electrostatic and ?-? interactions between the dye molecules and ACNPs. This approach is comprehensible and cost effective and can be utilized for dye removal in textile industries. 2023 Elsevier Inc. -
Cost-effective cryptographic architecture in quantum dot cellular automata for secured nano-communication
Quantum dot cellular automata (QCA) provide rapid computational efficiency, high density and low power consumption, which is an alternative for CMOS technology. In digital world, cryptography is an important feature to protect digital data. To ensure the data protection in nano-communication, a QCA-based cryptographic architecture is proposed in this article. In the proposed design, the encryption and decryption are done with the help of random keys which is produced by the pseudo random number generator (PRNG). In this paper, architectural component of cryptographic architecture includes XOR block, 1 to 4 de-multiplexer and PRNG, which are realised using QCA. Finally, an integration of the individual components through clock zone-based crossover, lead to the generation of a novel cryptographic architecture. This design achieves low cost compared to the existing literature, as it uses minimum number of majority gate and inverters with clock zone-based crossover. Copyright 2024 Inderscience Enterprises Ltd. -
Cost-effective route to nanodiamonds from low-rank coal and their fluorescent & dielectric characteristics
The synthesis of nanodiamonds from abundant and inexpensive precursors has recently piqued the curiosity of researchers. It has the potential to significantly reduce the cost of nanodiamonds and open up a plethora of new applications. In this work, fluorescent nanodiamonds with smaller particle sizes with rich surface functionality are synthesized from low-grade coal lignite by employing a facile acidic oxidation and ultrasonication approach. The extracted nanodiamond particles are hydrophilic and display high excitation-dependent fluorescence in the aqueous medium. The excitation-dependent fluorescence can be ascribed to the collaboration and competition of the OH and COOH functional groups. The as-synthesized nanodiamonds also show good dielectric permittivity and ac conductivity over a wide frequency range at room temperature. The present research opens up the possibility of mass production of nanodiamonds on the industrial scale from a low-cost precursor. 2021 -
Cost-enabled QoS aware task scheduling in the cloud management system
Maintaining the quality of service (QoS) related parameters is an important issue in cloud management systems. The lack of such QoS parameters discourages cloud users from using the services of cloud service providers. The proposed task scheduling algorithms consider QoS parameters such as the latency, make-span, and load balancing to satisfy the user requirements. These parameters cannot sufficiently guarantee the desired user experience or that a task will be completed within a predetermined time. Therefore, this study considered the cost-enabled QoS-aware task (job) scheduling algorithm to enhance user satisfaction and maximize the profit of commercial cloud providers. The proposed scheduling algorithm estimates the cost-enabled QoS metrics of the virtual resources available from the unified resource layer in real-time. Moreover, the virtual machine (VM) manager frequently updates the current state-of-the art information about resources in the proposed scheduler to make appropriate decisions. Hence, the proposed approach guarantees profit for cloud providers in addition to providing QoS parameters such as make-span, cloud utilization, and cloud utility, as demonstrated through a comparison with existing time-and cost-based task scheduling algorithms. 2021 - IOS Press. All rights reserved. -
Counseling and psychotherapy in india: Professionalism amidst changing times
India is a melting pot of diversity in castes, communities, geographical regions, languages, religions, and practices, within a geographical area of 32,87,263 kilometers, with 28 states and seven union territories. Although the notions of counseling and psychotherapy are Western, the process of mentoring and assisting individuals through their developmental issues was already present in ancient models of care in India, such as the Guru Shishya System,1 the Joint Family Network,2 and traditional healing. Counseling and psychotherapy do not exist as completely distinct disciplines in India. Although counseling grew out of a strong guidance format and led to a proliferation of trained and lay counselors and psychotherapy arose from a strong theoretical clinical psychology background, these differences are blurred in society. As Arulmani (2007) points out: all that is termed as counseling today was embedded within a complex support system of social relationships (p. 70). Although these fields progressed, difficulties with accreditation exist. The Indian Association of Clinical Psychologists (IACP), along with other bodies such as the Counseling Association of India, offer discussions of matters related to psychotherapy counseling and clinical psychology, and provide the code of conduct in India (IACP, 1993). Varma (1982) highlighted seven distinct features of the Indian population that strongly infiuence how counseling and psychotherapy are practiced and received by clients: Mutual interdependence, lack of psychological sophistication involving introspective and verbal abilities, social distance between the doctor and the patient due to class hierarchies, religious belief in rebirth and fatalism and related accountability, guilt attributed to misdeeds in past life and social approval-related shame, and lower emphasis on confidentiality as society can be therapeutic allies. India is a collectivistic society wherein the self is relational (Roland, 2005), though recent socio-economic changes have resulted in a contradictory mix of traditional and modern elements in families (Murthy, 2003). Shah and Isaac (2005) note that relationship problems dominate themes in clinical interviews and in the process of individual, couple and family therapy sessions in India. 2013 by Taylor & Francis Group, LLC. -
Counseling and Psychotherapy in India: Radha's Story
This chapter discusses the case of Radha, who presented with depression and infertility. The focus of counseling was to alleviate Radha's psychological distress, help her redefine her identity, and explore alternatives to infertility in the individual and marital context. The counselor's suggestion to use traditional healing practices, especially Pranayama, greatly helped the client, as she used these practices as for preventive coping. Handling the sensitive issue of infertility was challenging for the counselor, especially dealing with the ingrained cultural resistance to infertility and the client's value system that contributed to her own psychological state. Classical approaches to counseling and psychotherapy are indeed useful but require contextualization and an understanding of eclectic practice. Along with eclectic practice, integration of alternative systems of care, such as traditional healing practices, is seen as essential in the practice of counseling and psychotherapy in India. 2015 by the American Counseling Association. All rights reserved. -
Counselling and psychological wellbeing of people living with HIV in Kerala
There is a dearth in the documentation of the benefits of HIV-counseiling in India. This article deals with how HIV-counselling facilitates the psychological wellbeing of Persons Living with HIV (PLHIV) in Kerala, India. About 269 PLHIV participated in the study. Meaning in Life Questionnaire, Illness Perception Questionnaire and Psychological Wellbeing Scale were used. It was noticed that counselling did not impact the scores on subscales such as Timeline, Emotional Representation and Consequences, while the scores on Self-Acceptance and Autonomy did not differ even with counselling. Findings call for a reconsideration of the way HIV-counselling is provided. -
Countering educational disruptions through an inclusive approach: Bridging the digital divide in distance education
The COVID-19 pandemic has created havoc across the globe, irrespective of governments, industries, and societies. The education sector is one of the most extensively affected by the global health crisis, manifesting expansive negative consequences to learners from various age groups and socioeconomic statuses. Despite the predicaments posed by the pandemic, academic institutions continue to provide education through a distance learning approach. However, the educational disruptions have underscored the lack of digital resources and competencies, excluding poor and unconnected students. Likewise, transitioning to remote education exposed the digital divide and inequalities that have been neglected for a long time. If the ultimate objective is to provide distance education, it is vital to devise solutions to problems faced by underprivileged students. This chapter investigates these challenges that impede the successful adoption of distance education and offers strategies to counter the disruptions as it seems apparent that online education is here to stay. 2022, IGI Global. All rights reserved. -
COUPLE STRESS EFFECT ON FERRO-CONVECTION TRIGGERED BY CHEMICAL REACTION IN A POROUS LAYER WITH SPARSE DISTRIBUTION; [????? ??????? ?????????? ?? ?????????????, ??????????? ???????? ???????? ? ????????? ???? ? ??????????? ??????????]
The study delves into the impact of couple stress on the commencement of convection in a porous material oriented horizontally. This layer contains a chemically reactive ferromagnetic fluid and experiences bottom heating. The investigation utilizes small perturbation methodology to explore and understand the impact of couple stress on the initiation of convection in this specific system. With the assumption of a non-autocatalytic exothermic reaction, eigenvalues are determined utilizing the Galerkin method. The analysis explores the effects of magnetic and couple stress parameters, as well as the Frank-Kamenetskii number. The observation indicates that the acceleration of the onset of ferroconvection is influenced by both magnetic forces and chemical reactions. Simultaneously, the presence of the couple stress component serves to stabilize the system. Moreover, when the nonlinearity of magnetization is sufficiently pronounced, the destabilization of the fluid layer is observed to be marginal. 2024 Oles Honchar Dnipro National University;